Numéro d'image 32 de la section actuelle de Via Paleocapa Facade - Page 2 à 5 de Cosentino France

Via Paleocapa Facade

Flagship Project

DKTN provides a solution to the structural problems of this Italian façade

By Duesse Hi Tech

Numéro d'image 33 de la section actuelle de Via Paleocapa Facade - Page 2 à 5 de Cosentino France

Location

Bergamo, Italy

Matériau

DKTN

Couleur

Entzo

Quantity

158 m2

Architecture/design

Duesse Hi Tech

Application

Façades ventilée

End Date

2021

Épaisseur

12 mm

Starting point: a façade in natural stone facing some problems

In 2021, the partial restoration of a building situated at 3 Via Paleocapa in Bergamo (Italy) was successfully completed. The job consisted of replacing the existing ventilated façade, which was only 15 years old, with a more lightweight and equally beautiful one.

When the Duesse Hi Tech team took over the management of the project, they were faced with a building at serious risk of collapse due to the weight of the 250 m2 of natural stone - probably Calacatta of national origin - used on its façade. Furthermore, on the ground floor, designed as a portico supported on pillars, they found a 5 cm depression caused by the static load. The risk posed to the building and pedestrians -as it is a busy street in Bergamo- demanded quick action.

In addition to the excess weight of the natural stone, there was a technical problem with the anchoring system of the ventilated façade, which had been incorrectly designed in terms of static load bearing capacity. In the restoration, 12 mm DKTN Entzo slabs were used to replace the natural stone, thus significantly reducing the weight to about 50 kg per unit on each of the building’s walls.

Considering the urgency of replacing the façade, DKTN was the best option. The new design, the installation of the substructure and insulation layer, and the entire cladding were completed in just two weeks with a team of three people.

Numéro d'image 43 de la section actuelle de Via Paleocapa Facade - Page 2 à 5 de Cosentino France

Solution: DKTN technology without compromising on beauty

Having solved the technical challenges, it was necessary to find a material as beautiful as natural stone and with a finish similar to Calacatta. The wide range of DKTN colours made it possible to find the closest finish to the original cladding: Entzo. The result is the same chromatic and “natural” stone effect required by municipal and provincial authorities for areas of historic interest.

In short, DKTN ventilated façades are perfect both for the refurbishment of existing cladding and for new projects. There are five properties that make DKTN the perfect solution for ventilated façades: 1. Lightweight; 2. Large format slabs (Jumbo format 325 x 159 cm); 3. Quick installation; 4. Natural appearance; 5. High static and architectural performance.

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

“DKTN is the only synthetic material that is almost identical in appearance to natural stone. It is perfect for listed buildings”
Duesse Hi Tech

Duesse Hi Tech

Cosentino’s materials used in this project

Related Flagship Projects

Numéro d'image 59 de la section actuelle de Via Paleocapa Facade - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?

Numéro d'image 60 de la section actuelle de Lakeside Bank - Page 2 à 5 de Cosentino France

Lakeside Bank

Case Study

The technical challenge of a façade designed to impress

By Pappageorge Haymes Ltd.

Numéro d'image 61 de la section actuelle de Lakeside Bank - Page 2 à 5 de Cosentino France

Location

Illinois, United States

Matériau

DKTN

Couleur

Zenith

Quantity

465 m2

Architecture/design

Pappageorge Haymes Ltd.

Application

Rainscreen façade (concealed fastening)

Collaborator | Monteur

International Contracts Inc (ICI) |Stone Systems of Chicago

Épaisseur

12 mm

Cosentino team, coordination at all stages of the project

Lakeside is a well-known commercial bank in the Chicago area, Illinois. As part of the refurbishment process of some of their offices, specifically the Oakbrook Terrace office, they hired the services of the architectural studio Pappageorge Haymes Ltd. From the very beginning, the studio planned a modern, interesting façade that would catch the eye of passers-by, inviting them to look at it.

The execution of a stunning façade required a high quality material. Pappageorge had worked with natural stone in the past, but problems always arose because of its poor UV resistance and technical limitations. The studio had heard about the technical properties of DKTN on exterior façades and was keen to learn more.

The Cosentino team met with Pappageorge architects, provided material samples and designed a mock-up featuring the XL 45 system. In this rainscreen system, aluminum rails are anchored to the back of the DKTN slab by horizontal grooves. In the end, DKTN was the material of choice for the versatility it offered in such a complex project. Stone Systems of Chicago, a certified fitter knowledgeable of the material, was in charge of the execution of the project.

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

“It took us more than a year to overcome all the technical complexities of this 3D façade. Now, looking at the result, I can say that every minute was worth it”
Maritza Parada Arias

Maritza Parada Arias

Business Manager, Stone Systems of Chicago

The monolithic white of DKTN Zenith

After a difficult but very beautiful job under the direction of architect Donald Mouch, the Lakeside Bank façade is now one of the most impressive façades in Oakbrook Terrace, and the most beautiful ever executed by Stone Systems.

Without detracting from the flawless technical execution, a large part of the success is due to the beauty of the material. DKTN Zenith is part of the Solid Collection. Its near-perfect Nordic white blends excellently with the red brick used on the rest of the Lakeside Bank building, in a balanced mix of modernity and classicism.

A premium material for a first class institution: the Lakeside Bank has undoubtedly found its perfect match in DKTN. DKTN’s superior technical properties coupled with design aspects such as elegance, sobriety and perfection, make the Oakbrook Terrace building the most prominent of all Lakeside Bank buildings.

Cosentino’s materials used in this project

Related Flagship Projects

Numéro d'image 89 de la section actuelle de Lakeside Bank - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?

Numéro d'image 90 de la section actuelle de Cosentino Center Zurich - Page 2 à 5 de Cosentino France

Cosentino Center Zurich

Case Study

Contraste harmonieux

Pizrog Natursteine AG

Numéro d'image 91 de la section actuelle de Cosentino Center Zurich - Page 2 à 5 de Cosentino France

Location

Neuhaus, Suisse

Matériau

DKTN

Couleur

Danae

Application

Façades ventilée

Architecture/design

Pizrog Natursteine AG

End Date

2021

Épaisseur

12 mm

La façade combine le DKTN Danae lumineux avec l’ardoise naturelle sombre

Quand José Luis Moral décolle, le monde est à ses pieds. Le fervent pilote sportif survole les prairies et les collines boisées au nord du lac de Zurich et contemple un panorama alpin à couper le souffle. Les montagnes enneigées scintillent au-dessus, tout comme le lac en contrebas. Moral pose des surfaces pour les projets de construction individuels de ses clients depuis environ 30 ans, sur ses rives et bien au-delà. Avec Roandi Immobilien AG, il est devenu lui-même l’un des promoteurs.

Son attitude terre-à-terre lui profite également ici. De cette façon, Moral a pu trouver des emplacements logistiques idéalement situés dans une région très attrayante, à la fois pittoresque et commerciale, non seulement pour Pizrog Natursteine AG, dont il est le directeur, mais aussi pour un partenaire commercial important. L’utilisateur principal à Neuhaus est devenu le « Cosentino Center Zurich » avec 375 m² d’espace d’exposition et de bureau et 2325 m² d’espace de stockage. Le spécialiste du traitement individuel et de la pose de surfaces en pierre a déménagé avec son entreprise à Bubikon, à 15 km.

Numéro d'image 93 de la section actuelle de Cosentino Center Zurich - Page 2 à 5 de Cosentino France

Esthétique et fonctionnel

« Nous avons planifié et réalisé les deux bâtiments en parallèle avec un bureau d’architecture local. C’est ainsi que cela fonctionne toujours le mieux sur place », explique José Luis Moral. En même temps, il a établi des lignes directrices uniformes. « Le design riche en caractère est très important pour moi, ainsi que des fonctionnalités exceptionnelles et une qualité durable pour tous les articles Roandi. » Cela s’applique en particulier à l’enveloppe du bâtiment. La façade en rideau ventilé à l’arrière s’est avérée particulièrement efficace ici. Elle combine en permanence une efficacité énergétique élevée avec une grande liberté de conception.

« La façade avant doit être d’une luminosité invitante et rayonner d’une chaleur méditerranéenne claire, impression qui est renforcée par l’entrepôt sombre contrasté en arrière-plan », explique José Luis Moral. « Les matériaux sélectionnés doivent naturellement incarner les standards de qualité les plus élevés et la précision suisse proverbiale. Je pense que nous y sommes parvenus grâce à la combinaison de DKTN Danae et de schiste naturel. D’ailleurs, les deux matériaux viennent d’Espagne, tout comme moi », ajoute Moral avec un clin d’œil.

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Surface ultracompacte

Les minéraux naturels, la pression et la chaleur ont créé les deux surfaces utilisées. Cependant, cela peut prendre des millions d’années pour que les sédiments argileux deviennent du schiste. Avec DKTN by Cosentino, la métamorphose se produit de manière contrôlée et accélérée en quelques heures. À 25 000 tonnes de pression et 1200 °C, les minéraux sont formés en une surface ultracompacte à l’aide de la technologie d’aggloméré de particules (PST). DKTN est résistant au froid, à la chaleur, aux chocs thermiques et aux UV et offre des couleurs stables. Le matériau peut donc être utilisé à la fois à l’intérieur et à l’extérieur.

DKTN est produit en panneaux grand format allant jusqu’à 320 cm x 144 cm et en plus de 50 dessins et textures. Dans les projets Roandi, la nuance sablonneuse DKTN Danae de la Natural Collection de 1,2 cm d’épaisseur a été utilisée. Un treillis de fibre de verre intégré garantit qu’aucun fragment ne peut se détacher si la façade est endommagée. Cosentino a livré les plaques qui mesurent jusqu’à 160 x 110 cm découpées sur mesure, fendues en haut et en bas et avec des bords traités, directement sur le chantier de construction, numérotées consécutivement et « juste à temps ».

Numéro d'image 94 de la section actuelle de Cosentino Center Zurich - Page 2 à 5 de Cosentino France

Monolithe flamboyant

La sous-structure du revêtement extérieur se compose de supports en aluminium séparés thermiquement, qui sont fixés avec des ancrages à boulon au mur de béton, par ailleurs isolé avec de la laine de pierre de 19 cm. Les profilés en L verticaux sont fixés aux supports à l’aide de doubles rails en T horizontaux. Les plaques de DKTN fendues supérieures et inférieures ont été insérées dans ceux-ci et fixées en toute sécurité sur place par les installateurs de Pizrog Natursteine AG. « Avec ce système, vous travaillez très rapidement et en même temps avec une grande précision », explique Moral.

Étant donné que DKTN a un coefficient de dilatation thermique négligeable, les espaces entre les plaques individuelles peuvent être très petits. « Alors que de grandes fenêtres permettent de faire entrer beaucoup de lumière du jour à l’intérieur, la partie opaque de l’enveloppe du bâtiment a un caractère monolithique doucement chatoyant », dit, satisfait, José Luis Moral. Il va bientôt construire à nouveau avec Roandi. Un autre grand bâtiment commercial est en cours de construction juste à côté du « Cosentino Center Zürich », naturellement à nouveau dans la combinaison éprouvée avec DKTN Danae.

Numéro d'image 95 de la section actuelle de Cosentino Center Zurich - Page 2 à 5 de Cosentino France

Cosentino’s materials used in this project

Related Flagship Projects

Numéro d'image 111 de la section actuelle de Cosentino Center Zurich - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?

Numéro d'image 112 de la section actuelle de AEC Illuminazione - Page 2 à 5 de Cosentino France

AEC Illuminazione

Case Study

Sustainability in large format at the new AEC Illuminazione Technological Center

By SBGA Blengini Ghirardelli

Numéro d'image 113 de la section actuelle de AEC Illuminazione - Page 2 à 5 de Cosentino France

Location

Castelnuovo, Arezzo, Italy

Matériau

DKTN

Couleur

Domoos

Quantity

1,100 m2

Architecture/design

SBGA Blengini Ghirardelli Associati CTS and Lamec srl (fitter)

Application

Façades ventilée

End Date

2021

Épaisseur

12 mm

Large-scale passive building

The Innovation Technological Center (ITC) is a newly built building located within the AEC Illuminazione headquarters, where research and development work is carried out. The building has a surface area of 26,500 m2 and was designed by the Milanese architectural studio SBGA Blengini Ghirardelli, who based their design on pure, simple geometric lines. The heart of the project, known as “The Lab”, is formed by the intersection of two parallelepipeds in which, over an area of 3,000 m2, technicians and researchers work together in a space designed to encourage collaboration.

One of the most eye-catching features of this project is its northern façade. This façade, made of large-format DKTN Domoos slabs and with a surface area of 1,100 m2, is one of the largest DKTN façades in Europe. The cladding was installed on the ventilated façade using a Keil fixed anchoring system. The choice of material was based on the company’s sustainability criteria and the purpose of insulating the building from high temperatures.

DKTN Domoos is a finish from the Solid Collection. It is a dark, almost black shade, available in large format slabs (320cm x 144cm), which is ideal for outdoors and large surfaces and perfect for a ventilated façade.

In line with the company’s philosophy

The ITC building is the best example of AEC’s philosophy of innovation and automation. AEC’s business vision and investment decisions continually seek innovative solutions in the lighting of public spaces. The building creates an interesting relationship between the exterior and interior. The landscape outside serves as inspiration to create a relaxing atmosphere. The double-height entrance and the glazed façade provide a light-filled space where natural light prevails. Everything was designed with the wellbeing of employees in mind and nothing here is reminiscent of a traditional factory concept.

The building was built on three levels. On the ground and first floors, where tests and experiments are carried out under extreme environmental conditions, a series of double and triple height laboratories were set up from the mezzanine floor, from which it is possible to safely monitor the tests. The research offices are on the third floor. The clean, geometric lines continue on this floor. The building is completed by a skylight roof that brings light into the centre of the workspace. The technical systems and photovoltaic panels are located above the roof, concealed by a cornice, rounding off the project.

The most innovative and sustainable materials combined with avant-garde architecture have come together to create the ITC, which has become AEC’s best calling card.

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

“We chose DKTN Domoos for the north façade because it is a technological, resistant and sustainable material, capable of protecting the building”

SBGA Blengini Ghirardelli Associati

Cosentino’s materials used in this project

Related Flagship Projects

Numéro d'image 140 de la section actuelle de AEC Illuminazione - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?

Numéro d'image 141 de la section actuelle de Manhattan facade 7 West 51st - Page 2 à 5 de Cosentino France

Manhattan facade 7 West 51st

The technical challenge of bringing an old New York façade back to life

By MZA Architects

Numéro d'image 142 de la section actuelle de Manhattan facade 7 West 51st - Page 2 à 5 de Cosentino France

Location

New York, United States

Matériau

DKTN

Couleur

Danae | Edora | Borea

Application

Façade | Lobby floor | Interior walls

Architecture/design

MZA Architects | Stone Truss Systems as fitters

End Date

2021

Quantity

5,586 sq. ft.

Épaisseur

12 mm

The three dimensions of a renovated façade

At the end of 2019, the remodelling of an office building situated at 7 W 51st street in Manhattan was successfully completed. The design team responsible for the project, MZA Architects, planned a comprehensive renovation of the façade aimed at achieving a high-impact visual change. At the same time, the project aimed to find a technically feasible solution to the problem of dealing with an old structure in a dubious state of repair.

Both the architect and the developer visited Cosentino City New York to see first-hand DKTN’s technical and design possibilities for large outdoor surfaces. That first visit was enough to convince them of the suitability of DKTN for their project. They even chose three colours that matched the desired design concept. For the exterior façade they opted for DKTN Danae, a beige tone from the Natural Collection reminiscent of the sandy beach. For the lobby floor, they chose DKTN Edora, a shade in the same beige colour range as the façade, which creates a visual continuity between the exterior and interior of the building. Finally, for the interior walls of the building they chose DKTN Borea, a material reminiscent of wenge wood, which adds the stylish touch they were looking for in the renovation.

The result creates a balanced and warm look, in tan colours, which contrasts with the coldness of the typical black and white buildings of 1990s Manhattan.

“DKTN is undoubtedly the perfect fit for ventilated façades. It is as if DKTN was invented solely for this purpose”
Stephen Falk

Stephen Falk

Stone Truss Systems

Cut-to-size DKTN versatility

Having solved the first structural challenge, it was time to install DKTN and face the next challenges. For example, all corner details were made using mitres bonded to the panels, so they had to be perfectly manufactured and installed neatly taking into account adjacent panels. The different façade plans required detailed and meticulous manufacture.

DKTN can adapt to any system, and this project was no exception. For this project, Stone Truss Systems used KEIL stainless steel back anchors and placed a carbon mesh bonded to the slabs. They also used TS-179 aluminium horizontal wall rails, which were fixed to the substructure with anchor clips. In short, a masterpiece of construction that made it possible to install DKTN slabs firmly, without compromising the beauty of the original design.

The new façade of this building in the Diamond District, just a stone’s throw from Rockefeller Center, gives it an incredible look and makes it the envy of all its neighbours.

Cosentino’s materials used in this project

Related Flagship Projects

Numéro d'image 166 de la section actuelle de Manhattan facade 7 West 51st - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?

Numéro d'image 167 de la section actuelle de Ette Hotel - Page 2 à 5 de Cosentino France

Ette Hotel

Case Study

A DKTN façade to withstand Florida’s whimsical weather

By Jonathan Nehmer + Associates

Numéro d'image 168 de la section actuelle de Ette Hotel - Page 2 à 5 de Cosentino France

Location

Kissimmee, Florida, USA

Matériau

DKTN

Couleur

Odin

Quantity

4,800 sq. ft.

Architecture/design

Jonathan Nehmer + Associates, Inc.

Application

Façade

End Date

2021

Épaisseur

8mm

DKTN Odin, a unique look and feel of wood that stands the test of time

The Ette hotel is a newly built hotel in Kissimmee, Florida, USA. There are several Disney parks in the same city. As a result, the hotel welcomes thousands of tourists every year. This 126-room hotel attracts mainly families who, after their visits to the parks, make the pool area the centre of the hotel’s social life.

Both the architect and the project developer were clear about the properties of the material to be used in the construction and the façade of the pool area. They wanted a finish with the texture of natural wood which, at the same time, would blend in with the façade. Furthermore, the material needed to withstand the wear and tear of a busy area, sudden changes in temperature and even possible damage in a hurricane-prone state like Florida. In addition to the technical specifications, design played a key role: both the architect and the developer wanted the look and feel of wood for its beauty and warmth.

DKTN Odin stood out from the start as a very interesting option: firstly, because of its extraordinary strength and hardness which, together with its hazelnut colour, perfect for the modern and functional style of the hotel, provided the desired combination of strength and design; and secondly, because it also met the necessary requirements for installation with the Elemex Ceramitex Facades system.

A façade to withstand Florida’s humidity

Florida’s unique weather conditions demanded a façade with a PERS system. The Pressure-Equalised Rainscreen System (PERS) is designed to retain moisture and prevent water from reaching the structural substrate. An air layer provides the necessary capillary force and ventilation to facilitate drainage and drying.

The PERS system also uses a joint system, known as infill strips, that reduces the amount of water penetrating the façade. Under balanced pressure conditions, water cannot penetrate the building structure.

DKTN is also the perfect partner for the Elemex Ceramic Façade system installed at the hotel. This integrated attachment technology allows the use of mitered corners on 90% of the façade.

Once again, DKTN has become a very interesting façade cladding, this time at the Ette Hotel, where it meets the highest technical requirements without sacrificing on design.

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

“DKTN Odin’s wood-like finish, together with its ability to withstand the force of wind in a hurricane, were crucial in our choice”
Owen Blake

Owen Blake

Project Manager at Elemex Architectural Façade Systems

Related Flagship Projects

Numéro d'image 189 de la section actuelle de Ette Hotel - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?

Numéro d'image 190 de la section actuelle de TR House - Page 2 à 5 de Cosentino France

TR House

Case Study

Large format DKTN slabs to combine aluminium and glass on a façade

By RS Arquitectura

Numéro d'image 191 de la section actuelle de TR House - Page 2 à 5 de Cosentino France

Location

Sant Julià de Vilatorta, Barcelona, Spain

Matériau

DKTN

Couleur

Blanc Concrete

Quantity

350 m2

Architecture/design

RS Arquitectura

Application

Glued façade

End Date

2021

Épaisseur

8 mm

Blanc Concrete to blend the house into its surroundings

The RS Arquitectura studio is the mastermind behind this impressive single family home located in Sant Julià de Vilatorta, in the province of Barcelona (Spain). The creators of this project, which was successfully completed in August 2020, explain the creative concept and the challenges they faced.

The house is located in a prestigious area of natural beauty that RS Arquitectura wanted to highlight from the beginning of the project. For this purpose, the studio planned an L-shaped volume with pure and simple lines, which opens onto the garden and views, maintaining the necessary privacy and intimacy. The house has three levels, perfectly connected with each other, creating a seamless connection between the interior and exterior spaces.

The façade features three different claddings: DKTN is used as the main cladding, bringing elegance and subtlety to the space; then there is aluminium on the lower parts of the façade; finally, glass makes it possible to achieve this connection between the interior and exterior.

The finish chosen was DKTN Blanc Concrete. It is a material from the Tech Collection, reminiscent of concrete, which features small grey and beige veins on a white background. Its availability in large format slabs of 320 cm make it a perfect choice for a façade.

Numéro d'image 206 de la section actuelle de TR House - Page 2 à 5 de Cosentino France

A non-porous material to withstand humid climates

DKTN was used as the main cladding of the house. It was installed using a cladding system with mechanical fasteners and adhesive cement. In addition to its unquestionable beauty, when it came to choosing this finish, the peace of mind of working with a material of great quality and purity and with the backing of a highly professional company was paramount.

Cosentino provided RS Arquitectura with technical advice throughout the entire construction process on a number of aspects such as the cutting and how to make the most of each slab without compromising on design. Cosentino also collaborated in the design of the façade, the training of the personnel in charge of installing it and the monitoring of the entire project to ensure that there were no problems.

In terms of product features, in addition to the extraordinary size of the slabs, RS Arquitectura highly appreciated DKTN's zero porosity. In humid climates with large temperature contrasts, such as Sant Julià de Vilatorta, a non-porous material is the best guarantee that it will age well.

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

“We considered the possibility of using natural stone, specifically travertine, but we ruled it out because of its high price and porosity compared to DKTN, which also allowed us to work with larger pieces”
RS Arquitectura

RS Arquitectura

Cosentino’s materials used in this project

Blanc-Concrete-DKTN-1

Blanc Concrete

DKTN

Related Flagship Projects

Numéro d'image 222 de la section actuelle de TR House - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?

Numéro d'image 223 de la section actuelle de Cork Residential - Page 2 à 5 de Cosentino France

Cork Residential

Case Study

A DKTN Kira façade to withstand the Irish weather

Michael O’Brien

Numéro d'image 224 de la section actuelle de Cork Residential - Page 2 à 5 de Cosentino France

Location

Cork, Ireland

Application

Glued façade

Matériau

DKTN

Couleur

Kira

Monteur

Michael O’Brien

Épaisseur

1,2 cm

End Date

2020

An impressive façade made of five materials

This spectacular home in the heart of Cork was completed in 2020 The designer, Michael O’Brien, wanted to do something different on the façade and DKTN immediately came to mind. Michael had discovered DKTN in the showroom of Hickey Granite. When he first saw it, he was impressed with the size of the slabs and the material’s resistance to external factors such as ultra-violet rays, freezing and scratching.

DKTN Kira was fitted on the front façade of the home and on the side walls, which are highly exposed to unfavourable weather conditions. It was also used to frame the windows of the barbecue area (ground floor) in a more aesthetically pleasing way.

The uniqueness of the Ballycotton house lies in the five elements of its façade: DKTN, natural stone, plaster, zinc and wood. The combination of textures works perfectly in both visual and functional terms. The materials used are low maintenance and ideal for a house situated on a cliff top and exposed to Irish weather conditions.

DKTN Kira: the perfect combination with stone

Once DKTN had been selected, the next step was to choose the most suitable colour from an infinite number of options. Michael opted for the Kira colour because it best matched the stone. To do this, he ordered several samples from Cosentino and fitted them, along with the other materials, in the right place and exposed to the light they were to receive. He fell in love with Kira’s small grey veining and texture.

As for the cutting of DKTN Kira, although the original idea was to use it in a large seamless format, in the end O’Brien preferred to cut it into long pieces of different widths. By doing so, the façade achieves a visual effect of greater height.

In this home, twelve 12mm thick slabs were used to clad an area of 100m2. The slabs were ‘glued’ directly onto an existing façade, which precluded the use of other more efficient systems, such as a ventilated façade, but significantly reduced the cost.

The use of five materials, the irregular cutting and its installation with adhesive are the special features of this unusual façade. Without a doubt, the façade is the best introduction to this impressive home perched on the cliffs of Cork.

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Michael O’Brien

Michael O’Brien

Monteur

Cosentino’s materials used in this project

Related Flagship Projects

Numéro d'image 253 de la section actuelle de Cork Residential - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?

Numéro d'image 254 de la section actuelle de Westfield Newmarket - Page 2 à 5 de Cosentino France

Westfield Newmarket

Flagship project

DKTN Danae, a fresh new face for Newmarket's ventilated façade

By Scentre Group Sydney

Numéro d'image 255 de la section actuelle de Westfield Newmarket - Page 2 à 5 de Cosentino France

Location

Newmarket, Auckland, New Zealand

Matériau

DKTN

Couleur

Danae

Quantity

700m2

Architecture/design

Scentre Group Sydney | Westfield Design

Application

Façades ventilée

End Date

2020

Épaisseur

12mm

A ‘facelift’ for Westfield Newmarket

Westfield Newmarket shopping centre in central Auckland, New Zealand, reopened in August 2019. After 18 months of construction work, this shopping centre, which dates back to the 1980s, reopened its doors with a new look, 230 shops and 2,800 parking spaces.

The project involved the renovation and extension of the existing building, doubling its previous size and quadrupling the number of shops. After many months of work and an investment of 790 million dollars, the updated Newmarket rises majestically between 277 and 309 Broadway Street.

It was clear to the team of architects from the Scentre Group, the project developer, that the façade would play a key role in the renovation process. In addition to becoming the most eye-catching design feature, it had to incorporate the latest technology in terms of energy efficiency. A ventilated façade therefore appeared to be the most suitable choice. And for this ventilated façade, there was no better partner than DKTN.

The installation was carried out by the Eurotherm Facades NZ team. Two anchoring systems were used in the process: the Etem Alum Systemand the Keil Anchor. The technical support from Cosentino's headquarters in Spain was key to the successful execution, providing a prompt and professional advisory service whenever requested.

Sandy-coloured DKTN Danae

The new ventilated façade features 700m2 of 12mm DKTN Danae slabs. In addition to its clean, fresh look, DKTN Danae contrasts with the black window frames and the large glass surfaces.

DKTN Danae is a colour from the Natural collection that is reminiscent of the movement of sand. It is one of Cosentino's best-sellers as it works perfectly in almost any space. Furthermore, being a neutral colour, it is full of nuances that ensure its versatility and say goodbye to boredom.

In the case of the Westfield Newmarket shopping centre, this effect of movement is the result not only of the richness of the material -DKTN Danae- but also of its clever cutting: all along the façade, in a continuous pattern, one larger row is placed every four rows of slabs.

This feat of design aims to bring the Newmarket in line with the district where it is located: a thriving and trendy shopping area with the best tapas bars, the most alternative art galleries and the most authentic Maori arts and crafts.

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

Vous avez besoin d’aide sur un projet ?

Contactez nos spécialistes pour obtenir des conseils

“We chose DKTN because of the material’s structure, its warranty, its wide range of colours and its minimum thickness, perfect for ventilated façades”
Scentre Group Sydney

Scentre Group Sydney

Cosentino’s materials used in this project

Related Flagship Projects

Numéro d'image 278 de la section actuelle de Westfield Newmarket - Page 2 à 5 de Cosentino France

Voulez-vous connaître les possibilités de DKTN en matière de façades?